TORNADO CO., LTD

WEBJET 128

Card Type

ISDN TA

Chip Set

Unidentified

I/O Options

RJ-45 ISDN BRI U interface, 9-pin DTE port, power, microphone in, speaker out

ISDN Rate

230.4Kbps

ISDN Modulation Protocol

PPP, MLPPP, V.120

Error Correction/Compression

Unidentified

Data Bus

External

CONNECTIONS

Function

Label

Function

Label

ISDN BRI interface (RJ-45)

CN1

9-pin DTE port

CN4

Microphone in

CN2

Power

CN5

Speaker out

CN3

Power switch

SW1

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

DATA

Unidentified

On

DTR is high

DATA

Unidentified

Blinking

Serial data transfer active

DATA

Unidentified

Off

Serial data transfer not in progress

B1

Unidentified

On

B-channel 1 data call connected

B1

Unidentified

Off

No activity on B-channel 1

B2

Unidentified

On

B-channel 2 data call connected

B2

Unidentified

Off

No activity on B-channel 2

PWR

Unidentified

On

Power is on

PWR

Unidentified

Off

Power is off

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, E, Q, V, W, X

&F, &V

S Registers

S0, S2, S3, S4, S5, S7, S25

Note:

See MHI Help File for full command documentation.

Proprietary AT Command Set

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &M n [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

&M1

Synchronous connect mode and asynchronous off-line command mode.

&M2

Synchronous connect mode and asynchronous off-line command mode and set DTR high.

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Q n [cmds]

Description:

Selects communications mode options

Command

Mode

&Q0

Asynchronous mode, serial port speed follows connect speed.

&Q1

Asynchronous off-line command mode and synchronous connect mode.

&Q2

Asynchronous off-line command mode - modem autodials first number in directory, then synchronous connect mode.

&Q3

Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR.

&Q4

Auto-synchronous mode

&Q5

Error correction mode

DATA CARRIER DETECT (DCD)

Type:

Configuration

Format:

AT [cmds] &C n [cmds]

Description:

Selects whether the DCD option is enabled or disabled

Command

Function

&C0

DCD enabled

&C1

DCD enabled after carrier signal detected

&C2

DCD enabled when on-line, low at loss of carrier, enabled again at idle

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &S n [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is connected

&S2

DSR high only while modem is connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &D n [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

&Q Setting

&D0

&D1

&D2

&D3

&Q0, &Q5

Command 0

Command 1

Command 2

Command 4

&Q1

Command 2

Command 1

Command 2

Command 4

&Q2

Command 2

Command 2

Command 2

Command 2

Command

Function

Command 0

Modem does not respond to DTR

Command 1

Modem goes to command mode after DTR goes is off

Command 2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

Command 3

Modem is initialized after DTR goes off

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &K n [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K1

RTS to CTS flow control enabled

&K2

XON/XOFF flow control enabled

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

HOOK CONTROL

Type:

Immediate

Format:

AT [cmds] H n [cmds]

Description:

Selects whether the modem is on-hook or off-hook

Command

Function

H0

Modem commanded to go on-hook (hang-up)

ON-LINE

Type:

Immediate

Format:

AT [cmds] O n [cmds]

Description:

Controls on-line command (data transmission) state options.

Note: The O command must be placed at the end of the command string.

Command

Function

O0

On-line command mode with no retraining enabled

PROTOCOL SELECTION

Type:

Configuration

Format:

AT [cmds] &O n [cmds]

Description:

Selects active protocol

Command

Mode

&O7

PPP, 1 x B

&O8

V.14, 1 x B

&O9

V.110, 1 x B

&O10

V.120, 1 x B

&O13

Multi Link V.120, 2 x B

&O16

GCI-speech, 2 x B

&O18

GCI-data, 2 x B

&O27

Multi Link PPP, 2 x B

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] I n [cmds]

Description:

Displays information requested

Command

Function

I0

Reports hardware identification

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports product name and software revision

I4

Reports manufacturer information

I5

Reports protocol options

I8

Reports Euro-ISDN software version

RESTORE PROFILE ON POWER-UP

Type:

Configuration

Format:

AT [cmds] &Y n [cmds]

Description:

Restores a selected profile into the active profile on power-up (hard reset).

RTS/CTS

Type:

Configuration

Format:

AT [cmds] &R n [cmds]

Description:

Command function currently unidentified

SOFT RESET

Type:

Immediate

Format:

AT [cmds] Z n [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

STORE ACTIVE PROFILE

Type:

Configuration

Format:

AT [cmds] &W n [cmds]

Description:

Writes the values for the active profile into the non-volatile RAM

EXTENDED AT COMMANDS

CONFIGURATION PROFILES

Type:

Immediate

Format:

AT [cmds] /S [cmds]

Description:

Displays active and stored configuration profiles

SPECIAL COMMANDS

PROTOCOL SELECTION

Type:

Configuration

Format:

AT [cmds] #CH= n [cmds]

Description:

Selects active protocol

Command

Mode

#CH=7

PPP, 1 x B

#CH=8

V.14, 1 x B

#CH=9

V.110, 1 x B

î

V.120, 1 x B

#CH=13

Multi Link V.120, 2 x B

#CH=16

GCI-speech, 2 x B

#CH=18

GCI-data, 2 x B

#CH=27

Multi Link PPP, 2 x B

REMOTE NUMBER SELECTION

Type:

Configuration

Format:

AT [cmds] #REMNBRC= n [cmds]

Description:

Selects remote control number

REMOTE PASSWORD SELECTION

Type:

Configuration

Format:

AT [cmds] #PASSRC= n [cmds]

Description:

Selects remote control password

RING MODE

Type:

Configuration

Format:

AT [cmds] #RM= n [cmds]

Description:

Selects ring mode

Command

Mode

#RM0

Selects ring mode by subnumber or MSN

#RM1

Pass on call to active profile

SOFT RESET

Type:

Immediate

Format:

AT [cmds] #Z n [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

STORED PROFILES

Type:

Immediate

Format:

AT [cmds] #V [cmds]

Description:

Displays list of stored parameters in short form

S(STATUS) -REGISTERS

ACTIVE PROFILE

Type:

Register

Format

AT [cmds] S110= n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Selects active profile

AUTOBAUD

Type:

Register

Format

AT [cmds] S124= n [cmds]

Description:

Enables/disables autobaud function

Command

Function

S124=0

Autobaud disabled

S124=1

Autobaud enabled

BIT-MAPPED REGISTER S112

Format:

AT [cmds] S112= n [cmds]

Range:

Unidentified

Unit:

Bit-mapped

Description:

Controls ring message format

Bit

Value

Function

0

0

1

Standard AT RING message format (RING)

Extended AT RING message format (RING J

1

0

1

Extended result codes disabled

Extended result codes enabled

2

0

Not used

3

0

1

Standard AT format

Extended AT format

6 - 4

0

Not used

7

0

1

Additional service messages disabled

Additional service messages enabled

DTR COMMAND

Type:

Register

Format

AT [cmds] S123= n [cmds]

Description:

Enables &D command

Command

Function

S123=0

&D enabled for DTR functions

S123=1

DTR ingnored. &D command disabled

EXTENDED RESULT CODES

Type:

Register

Format

AT [cmds] S95= n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Works in combination with the W n command to enable extended result codes. Features enabled by S95 take precedence over the options selected by W n .

Bit

Value

Function

0

0

1

CONNECT result code reports DTE speed.

CONNECT result code reports line speed instead DTE speed.

1

0

1

Verbose CONNECT result codes display DTE or line speed only.

Adds "/ARQ" to all verbose CONNECT result codes except "NONE."

2

0

1

CARRIER result codes disabled.

CARRIER result codes enabled.

3

0

1

PROTOCOL result codes disabled.

PROTOCOL result codes enabled.

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] S121= n [cmds]

Range:

0-255

Description:

Sets values in active profile to values found in the default profile

Command

Function

S121=0

Retrieve factory settings and restart

S121=255

Disabled

FLOW CONTROL

Type:

Register

Format

AT [cmds] S39? [cmds]

Description:

Displays the current flow control

Value

Meaning

0

Flow control disabled

3

RTS/CTS flow control enabled

4

XON/XOFF flow control enabled

PROTOCOL SERVICE

Type:

Register

Format

AT [cmds] S111= n [cmds]

Description:

Selects options for protocol service

Command

Function

1

Voice service

2

Data modem service

3

Raw data service

4

Group 3 fax service

5

V.14

7

PAD service

8

V.120 service

10

Synchronous relay service

RING MESSAGE TIMER

Type:

Register

Format

AT [cmds] S117= n [cmds]

Range:

0-255

Unit:

1 second

Description:

Maximum duration allowed between two consecutive RING messages

Note: S117=0 allows for a single RING message only

SERIAL ASYNCHRONOUS RATE & CLOCK SELECTION

Type:

Register

Format

AT [cmds] S114= n [cmds]

Description:

Selects sserial asynchronous speed & clock selection

Command

Function

S114=0

External clock source

S114=1

1200bps

S114=2

2400bps

S114=3

300bps

S114=4

4800bps

S114=7

7200bps

S114=9

9600bps

S114=12

1200bps

S114=14

14.400bps

S114=19

19.2Kbps

S114=24

2400bps

S114=28

28.8Kbps

S114=38

38.4Kbps

S114=48

4800bps

S114=20

57.6Kbps

S114=72

7200bps

S114=75

75bps

S114=96

9600bps

S114=115

115.2Kbps

S114=255

Internal clock source

SOFT RESET

Type:

Immediate

Format:

AT [cmds] S122= n [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

Command

Function

S122=0

Restore setting

S122=255

Disabled