MEDIAFORTE PRODUCTS PTE., LTD.

MOMENTA K56X EXTERNAL MODEM

Card Type

Modem/Fax card

Chip Set

Unidentified

I/O Options

Line out, line in, DTE port, power, microphone, speaker

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A

ITU-T V.22, V.22bis, V.32, V.32 bis, V.34, K56 flex, V.80

Fax Modulation Protocol

ITU-T V.17, V21CH21, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

External

CONNECTIONS

Function

Label

Function

Label

Line out

CN1

Power

CN4

Line in

CN2

Microphone in

CN5

Serial port

CN3

Speaker out

CN6

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

MR

Unidentified

On

Modem is receiving power

MR

Unidentified

Off

Modem is not receiving power

TR

Unidentified

On

DTR signal is high

TR

Unidentified

Off

DTR signal is low

SD

Unidentified

On

Modem transmitting data

SD

Unidentified

Off

Modem not transmitting data

RD

Unidentified

On

Modem is receiving data

RD

Unidentified

Off

Modem is not receiving data

OH

Unidentified

On

Modem is Off-hook

OH

Unidentified

Off

Modem is on-hook

RS

Unidentified

On

RTS signal is high

RS

Unidentified

Off

RTS signal is low

CS

Unidentified

On

CTS signal is high

CS

Unidentified

Off

CTS signal is low

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, B, E, H, M, O, P, Q, S, T, V, X, Y, Z

&C, &P, &R, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \K, \N

%C, %E, %L, %Q

Special Commands

+MS

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40

S41, S46, S48, S82, S86, S91, S92, S95

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

í N1

Auto-mode detection enabled

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

&M1

Synchronous connect mode 1

&M2

Synchronous connect mode 2

&M3

Synchronous connect mode 3

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode. Same as &M

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR on in on-line mode, off in command mode

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

&D0

DTR is ignored (assumed on)

&D1

Modem goes to command mode after DTR goes is off

í &D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

&D3

Modem is initialized after DTR goes off

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DS=n

Dial stored telephone number n (n=0-3)

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D&

Wait for bong tone

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

&F0

Sets values to factory configuration 0

&F1

Sets values to factory configuration 1

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Note: Used primarily for international data transmission

Command

Function

&G0

Guard tone disabled

&G1

Guard tone disabled

&G2

1800Hz guard tone enabled

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

&K6

XON/XOFF and RTS/CTS flow control enabled

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports firmware revision an device ID

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

í L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting