BOCA RESEARCH, INC.

SOUND EXPRESSION (SE34SRS),

SOUND EXPRESSION (SE34SVD)

Card Type

Sound/Modem card

Chip Set

Unidentified

Maximum Onboard Memory

Unidentified

I/O Options

Game/MIDI port, CD-ROM interface - IDE, Audio in - CD-ROM (3), speaker, line out, line in, microphone in, telephone jack

Maximum Modem Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A

ITU-T V.22, V.22bis, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

16-bit ISA

CONNECTIONS

Function

Location

Function

Location

Game/MIDI port

CN1

Wavetable

CN6

Speaker

CN2

CD-ROM interface - IDE

CN7

Line out

CN3

Audio in - CD-ROM (Mitsumi)

J9

Line in

CN4

Audio in - CD-ROM (Panasonic)

J10

RJ-11 telephone jack

CN5

Audio in - CD-ROM (Sony/IDE)

J11

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘comma’, A/

A, B, C, E, H, L, M, O, Q, R, S, T, U, V, W, X, Y, Z

&C, &F, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B

%C, %E, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30,S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92,

S95

Special Commands

+MS?, +MS

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

D

Dial

DL

Re-dial last number

DP

Pulse dialing enabled

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

D^

Disable dialing code.

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product ID

I1

Reports checksum

I2

Tests and reports ROM checksum

I3

Reports firmware revision

I4

Reports OEM-defined identifier string.

I5

Reports country code

I6

Reports modem data pump model

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

í N1

Permits handshaking at any speed supported by both modems.

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

&Q Setting

&D0

&D1

&D2

&D3

í &Q0, &Q5, &Q6

Command 0

Command 3

Command 2

Command 4

&Q1, &Q4

Command 1

Command 3

Command 2

Command 4

&Q2, &Q3

Command 2

Command 2

Command 2

Command 2

Command

Function

Command 0

Modem does not respond to DTR

Command 1

Modem disconnects (hangs up) after DTR goes off; Auto-Answer not affected

í Command 2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

Command

3

Asynchronous escape sequence

Command 4

Modem does a soft reset

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

í &K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Enable transport XON/XOFF

&K6

Enable both RTS/CTS and XON/XOFF

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal

Command

Break from DTE

Break from DTE during Direct Mode

Break received from remote modem

\K0

Online command mode enabled, send no break to remote modem

Break sent to remote modem and command entered

Buffers cleared, break sent to DTE

\K1

Break sent to remote modem and buffered cleared

Break sent to remote modem and command entered

Buffers cleared, break sent to DTE

\K2

Online command mode enabled, send no break to remote modem

Send break with transmitted data

Break sent immediately to DTE

\K3

Send break to remote modem immediately

Break sent to remote modem and command entered

Break sent immediately to DTE

\K4

Online command mode enabled, send no break to remote modem

Send break with transmitted data

Break sent with received data to the DTE

í \K5

Send break with transmitted data

Send break with transmitted data

Break sent with received data to the DTE

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

MNP reliable mode enabled

\N3

Auto-reliable mode or MNP auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

V.42 auto-reliable mode or MNP auto-reliable mode enabled

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

í S37=0

Speed of last connection

S37=1-3

300bps

S37=4

Reserved

S37=5

1200bps

S37=6

2400bps

S37=7

V.23 mode

S37=8

4800bps

S37=9

9600bps

S37=10

12.0Kbps

S37=11

14.4Kbps

S37=12

7200bps

RESULT CODES

BASIC RESULT CODES

Numeric

Verbose

Wn

Function

0

OK

W0

Modem has successfully executed the previous command and has returned to the on-line command state.

1

CONNECT

W0

Connection established at unspecified rate.

2

RING

W0

Incoming ring detected.

3

NO CARRIER

W0

Carrier signal lost or no connection established.

4

ERROR

W0

Last command issued was not valid.

5

CONNECT 1200

W0

Connection established at 1200bps.

6

NO DIALTONE

W0

No dial tone was detected within the time allotted by S7.

7

BUSY

W0

A busy tone was detected after dialing.

8

NO ANSWER

W0

No quiet answer (ring-back followed by silence) was detected.

9

CONNECT 600

WO

Connection established at 600bps

10

CONNECT 2400

W0

Connection established at 2400bps.

11

CONNECT 4800

W0

Connection established at 4800bps.

12

CONNECT 9600

W0

Connection established at 9600bps.

13

CONNECT 7200

WO

Connected as data modem during answer.

14

CONNECT 12000

WO

Connection established at 12000bps.

15

CONNECT 14400

W0

Connection established at 14.4K bps.

16

CONNECT 19200

W0

Connection established at 19.2K bps.

17

CONNECT 38400

W0

Connection established at 38.4K bps.

18

CONNECT 57600

W0

Connection established at 57.6K bps.

19

CONNECT 115200

W0

Connection established at 115.2K bps.

BASIC RESULT CODES (cont'd)

Numeric

Verbose

Wn

Function

22

CONNECT 75/1200

W0

Connection established at transmit 75/receive 1200bps.

23

CONNECT 1200/75

W0

Connection established at transmit 1200/receive 75bps.

24

DELAYED

WO

Connection fails and number dialed is "delayed" due to country blacklisting.

32

BLACKLISTED

WO

Connection failed and the number dialed is considered "blacklisted"

33

FAX

W0

Fax connection established.

35

DATA

W0

Data connection established.

EXTENDED RESULT CODES

Numeric

Verbose

Wn

Function

40

CARRIER 300

W1

Carrier signal at 300bps is detected.

44

CARRIER 1200/75

W1

Carrier signal at transmit 1200/receive 75bps is detected.

45

CARRIER 75/1200

W1

Carrier signal at transmit 1200/receive 75bps is detected.

46

CARRIER 1200

W1

Carrier signal at 1200bps is detected.

47

CARRIER 2400

W1

Carrier signal at 2400bps is detected.

48

CARRIER 4800

W1

Carrier signal at 4800bps is detected.

49

CARRIER 7200

W1

Carrier signal at 7200bps is detected.

50

CARRIER 9600

W1

Carrier signal at 9600bps is detected.

51

CARRIER 12000

W1

Carrier signal at 12.0K bps is detected.

52

CARRIER 14400

W1

Carrier signal at 14.4K bps is detected.

53

CARRIER 16800

W1

Carrier signal at 16.8K bps is detected.

54

CARRIER 19200

W1

Carrier signal at 19.2K bps is detected.

55

CARRIER 21600

W1

Carrier signal at 21.6K bps is detected.

56

CARRIER 24000

W1

Carrier signal at 24.0K bps is detected.

57

CARRIER 26400

W1

Carrier signal at 26.4K bps is detected.

58

CARRIER 28800

W1

Carrier signal at 28.8K bps is detected.

59

CONNECT 16800

W0

Connection established at 16.8K bps.

61

CONNECT 21600

W0

Connection established at 21.6K bps.

62

CONNECT 24000

W0

Connection established at 24.0K bps.

63

CONNECT 26400

W0

Connection established at 26.4K bps.

64

CONNECT 28800

W0

Connection established at 28.8K bps.

66

COMPRESSION: CLASS 5

W1

MNP Class 5 data compression was negotiated.

67

COMPRESSION: V.42BIS

W1

V.42bis data compression was negotiated.

69

COMPRESSION: NONE

W1

No data compression was negotiated.

70

PROTOCOL: NONE

W1

No protocol was negotiated.

77

PROTOCOL: LAP-M

W1

V.42 LAPM error-control was negotiated.

80

PROTOCOL: ALT

W1

MNP error-control was negotiated.

81

PROTOCOL: ALT-CELLULAR

W1

Modem connected in the MNP10 mode.