EVENTIDE, INC.

WLZ-320 (FOR HP SERIES 200, 300, & 400)

NIC Type

Ethernet

Transfer Rate

10Mbps

Data Bus

Hewlet-Packard backplane DIO bus.

Topology

Linear Bus

Wiring Type

RG58A/U 50ohm coaxial

AUI transceiver via DB-15 port

Boot ROM

Available (Card comes standard with a Boot ROM)

CABLE TYPE

Type

JP4A - JP4F

JP8

JP10

»

RG58A/U 50ohm coaxial

Pins 2 & 3 closed

Pins 2 & 3 closed

Pins 2 & 3 closed

 

AUI transceiver via DB-15 port (10Base5)

Pins 1 & 2 closed

Pins 2 & 3 closed

Pins 1 & 2 closed

 

AUI transceiver via DB-15 port (10Base2)

Pins 1 & 2 closed

Pins 1 & 2 closed

Pins 1 & 2 closed

INTERRUPT REQUEST

IRQ

SW1/1

SW1/2

 

3

On

On

 

4

Off

On

»

5

On

Off

 

6

Off

Off

Note:The manufacturer warns that this option should not be altered from the default.

FACTORY CONFIGURED SETTINGS

Function

Switch

Setting

Remote Console

SW1/3

On

ROM DTACK

SW1/4

On

CARD SELECT CODE

Code

SW1/1

SW2/2

SW2/3

SW2/4

SW2/5

 

16

Off

On

On

On

On

 

17

Off

On

On

On

Off

 

18

Off

On

On

Off

On

 

19

Off

On

On

Off

Off

 

20

Off

On

Off

On

On

»

21

Off

On

Off

On

Off

 

22

Off

On

Off

Off

On

 

23

Off

On

Off

Off

Off

 

24

Off

Off

On

On

On

 

25

Off

Off

On

On

Off

 

26

Off

Off

On

Off

On

 

27

Off

Off

On

Off

Off

 

28

Off

Off

Off

On

On

 

29

Off

Off

Off

On

Off

 

30

Off

Off

Off

Off

On

 

31

Off

Off

Off

Off

Off

Note:If more than one card is used in a single computer, each card must be set to a different code.

BOOT ROM ADDRESS

Boot ROM Address

SW2/6

SW2/7

SW2/8

SW2/9

20000h

Off

On

On

On

40000h

On

Off

On

On

60000h

Off

Off

On

On

80000h

On

On

Off

On

A0000h

Off

On

Off

On

C0000h

On

Off

Off

On

E0000h

Off

Off

Off

On

100000h

On

On

On

Off

120000h

Off

On

On

Off

140000h

On

Off

On

Off

160000h

Off

Off

On

Off

180000h

On

On

Off

Off

1A0000h

Off

On

Off

Off

1C0000h

On

Off

Off

Off

1E0000h

Off

Off

Off

Off

BOOT ROM REVISION

Revision

SW2/10

»

3.0 or later

On

 

Earlier than 3.0

Off

Note:The boot ROM revision number is, in most cases, displayed when the system is booted. If the switch is set to On when it should be set to Off, the following message will be displayed: "Wrong Boot ROM Version (1.0, 2.0, or 3.0L) Please change config switch on LAN card". If the switch is set to Off when it should be set On, the card will not be recognized, and will not log into the network.