1 6 0 6 8 6 COMPAQ NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 1024| | Capacity form/unform 106/ MB Heads 2| 12| | Seek time / track 16.0/ 5.0 ms Sector/track | 17| | Controller IDE / AT Precompensation 65535 Cache/Buffer 32 KB SEGMENTED Landing Zone Data transfer rate 2.800 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle 3.9 W Shock g 10 | 75 seek 4.6 W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h 250000 Warranty Month 12 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SEAGATE ST3290 FAMILY INSTALLATION GUIDE 36237-002, REV. A 6/1993 +---------------------------------------------------------+ | +----+J5 |XX J1 | ++LED +----1 |XX | ++2-pin |XX | |XX I | |XX N | |XX T | |XX E | |XX R | |XX F | |XX A | |XX C | |X1 E | | | |XX J3 | |XX Power +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SEAGATE ST3290 FAMILY INSTALLATION GUIDE 36237-002, REV. A, 6/1993 Jumper Setting ============== J5 Master/Slave Jumper Block ---------------------------- +8-6-4-2+ |o o o o| The drive is a master; there is no slave. |o o o o| +7-5-3-1+ +8-6-4-2+ |o o X o| Master in a two drive system |o o X o| +7-5-3-1+ +8-6-4-2+ |o o o X| The drive is a slave to a ATA compatible master. |o o o X| NOTE: Do not configure the drive as a slave to a +7-5-3-1+ non-ATA-compatible master. +8-6-4-2+ |o o | Pins 5 & 6, and 7 & 8 are factory reserved. |o o | Don't use them! (OPEN) +7-5-3-1+ J3 DC Power and pin connector assignments ------------------------------------------- -------------------+ --+ +-----J3-----+| pin 1 +12 VDC 1| | 4 3 2 1 || pin 2 +12 Volts Return -+ \------------/| pin 3 + 5 Volts Return ------------------+ pin 4 + 5 VDC ********************************************************************** I N S T A L L ********************************************************************** SEAGATE ST3290 FAMILY INSTALLATION GUIDE 36237-002, REV. A, 6/1993 Notes on Installation ===================== Mounting the drive ------------------ Mount the drive securely in any orientation using either the bottom or side mounting holes. NOTE Make sure you mount the drive so that you do not strain the cables. Bottom mounting holes --------------------- Insert four 6-32 UNC-2A screws not more than 0.20 inches (6 turns) into the drive frame. Side mounting holes ------------------- Insert four 6-32 UNC-2A screws not more than 0.13 inches (4 turns) into the drive frame. CAUTION If you use a screw that is too long, you cold damage the drive. Attaching cables ---------------- 1. Turn off the system power 2. Put on a grounded wrist strap. 3. Attach the 40-pin AT interface cable. Attach one end of the cable to the drive interface connector and the other end to the interface connector on the host adapter or the host system mother- board. If you are installing two drives, use a daisy-chain cable. Verify that pin 1 of the interface cable is matched to pin 1 of the interface connector on the drive and on the host computer. Pin 1 is usually deenoted by a stripe on the side of the ribbon cable. 4. Attach the power cable. Attach a system power cable to the drive power connector.