D 3 7 3 5 NEC Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1084| 537| | Capacity form/unform 44/ MB Heads 2| 4| | Seek time / track 23.0/ ms Sector/track 41| 41| | Controller IDE / AT Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 1.500 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek 10.0 W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 50000 Warranty Month Lift/Lock/Park NO Certificates ********************************************************************** L A Y O U T ********************************************************************** NEC D3735 INSTALLATION GUIDE DEC. 92 +---------------------------------------------------------+ | JP13+-+| | JP12+-+| | JP11+-+| | +-+| I | 40XX N | |XX T | |XX E | |XX R | |XX F | |XX A | +--JP17 |XX C | +--+ |XX E | 3 2 1 |X1 | +-+LED | | +-+CONNECTOR +-------+ |XX | +-------+ |XX Power +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** NEC D3735 INSTALLATION GUIDE DEC. 92 Jumper Setting ============== JP12/JP13 Master/Slave ----------------------- +-------------+--------------+--------------------------------+ | D37x5 | D3765 | Function | +------+------+------+-------+--------------------------------+ | JP12 | JP13 | JP12 | JP13 | | +------+------+------+-------+--------------------------------+ |OPEN |OPEN |CLOSED|CLOSED | Single drive (default setting) | +------+------+------+-------+--------------------------------+ |CLOSED|OPEN |OPEN |CLOSED | Master (dual drive system) | +------+------+------+-------+--------------------------------+ |CLOSED|CLOSED|OPEN |OPEN | Slave (dual drive system) | +------+------+------+-------+--------------------------------+ JP17 Power Mode Jumper ----------------------- +---------+ | O--O O | +-1--2--3-+ 1-2 CLOSED Auto power save mode disabled 2-3 CLOSED Auto power save mode enabled The other jumpers are reserved for factory use! ********************************************************************** I N S T A L L ********************************************************************** NEC D3735/3781/3772 INSTALLATION GUIDE DEC. 92 REV. A NOTES ON INSTALLATION ===================== First install the drive with the components side to the bottom. Connect the system power and interface cables to the drive connectors. Both connectors are keyed and can only be connected one way. The interface connector may not be keyed. In this case check if the red edge of the interface cable is connected to the pin 1 of the drive connector. After installing the hardware please turn on your computer system and run the setup program. Please identify which model has to be installing and use the NEC recommended drive parameter for the set up setting. For this purpose edit the logical parameters into the "User type 47/48". The IDE interface accept two drives (Master/Slave). For a dual drives installation jumper both drives. The Master/Slave operation is guranteed only with NEC disk products. In order to install DOS please run the DOS program FDISK and Format C:/s accordingly. In case of installation trouble please contact NEC hotline: Tel. 49/89/93006 708 Caution: IDE drives don't need a low level format. If a new low level format become neccessary, please run only qualified programs for IDE devices like WDFMT.EXE by use of physical parameters. ********************************************************************** F E A T U R E S ********************************************************************** NEC NEC DRIVES INSTALLATION GUIDE DEC. 92 REV. A NEC drives ----------- The NEC IDE/SCSI drives are designed to work in the IBM AT and compatible systems and gurantee the operation with any standard IDE and SCSI Controller. Further, the NEC drives provide compatibility to the ATA/SCSI CAM and ANSI (X3-131-199x) standard as well as to all known operating systems.