M R 5 3 5 R MITSUBISHI NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/HH Cylinders 977| | | Capacity form/unform 60/ MB Heads 5| | | Seek time / track 28.0/ 5.0 ms Sector/track 26| | | Controller RLL / ST506 Precompensation 300 Cache/Buffer KB Landing Zone Data transfer rate 0.938 MB/S int Bytes/Sector 512 0.938 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 10 50 | -40 60 Power: sleep W Humidity % 8 80 | 5 95 standby W Altitude km 2.000| 12.000 idle W Shock g 2 | 30 seek 20.0 W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit 32 MTBF h 30000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MITSUBI. MR535 OPERATION AND MAINTENANCE MANUAL IB-67124-A +---------------------------------------------------------+ | |XX | |XX J2 | |XX | |XX | SW2 8--+ | 1 | | | |XX | | | |XX | | | |XX | | | |XX | 1--+ |XX J1 | SW1 6--+ |XX | | | |XX | | | |XX | 1--+ |XX | | 1 | |XX J6 | |XX Power +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** MITSUBI. MR535 OPERATION AND MAINTENANCE MANUAL IB-67124-A Jumper Setting ============== There are two switches on the main circuit board of this drive. SW1 Termination Switch ---------------------- +-----------+ |o o o o o o|ON |x x x x x x|OFF +1-2-3-4-5-6+ +-+-+-+-+-+------- Termination Switch To provide termination for the last unit, al switches of SW1 should be set in the ON position. On all other units, all the switches of SW1 should be set in the OFF position. SW2 Drive Select ----------------- +---------------+ |x o o o x o o o|ON |o x x x o x x x|OFF +1-2-3-4-5-6-7-8+ | | | | | | | +--- Set OFF position | | | | | | +----- Set OFF position | | | | | +------- Set OFF position | | | | +--------- RADIAL (R) | | | +----------- Drive Select 1 (DS1) | | +------------- Drive Select 2 (DS2) | +--------------- Drive Select 3 (DS3) +----------------- Drive Select 4 (DS4) In multiple unit connection it is necessary to configure each drive with a unique address. +-----------+---------------------------+ | SW2 |Drive Select Configuration | +----+------+------+-----+----+---------+ |Bit |*Mark | 1 | 2 | 3 | 4 | +----+------+------+-----+----+---------+ | 1 | DS1 | ON | OFF |OFF |OFF | +----+------+------+-----+----+---------+ | 2 | DS2 | OFF| ON |OFF |OFF | +----+------+------+-----+----+---------+ | 3 | DS3 | OFF| OFF |ON |OFF | +----+------+------+-----+----+---------+ | 4 | DS4 | OFF| OFF |OFF |ON | +----+------+------+-----+----+---------+ *Mark is printed on Printed Circuit Board (PCB). The control cable allows for a daisy chain connection of up to four drives. The switch block has DRIVE SELECT switched off with the "radial" option selected. Each drive is shipped with the switch block marked "R" switched on, resulting in the daisy chain operation. In this case, input and output signals are enabled when the appropriate DRIVE SELECT line is activated. When the switch block marked "R" is switched off, all inout and out- put signals are enabled even if the drive is not selected. However, the front panel LED will not be on. DRIVE SELECT must be activate to light the LED. J6 DC Power and pin connector assignments ------------------------------------------- +--------------+ |+-----J3-----+| pin 1 +12 VDC || 1 2 3 4 || pin 2 +12 VDC Return |+------------+| pin 3 + 5 VDC Return +--------------+ pin 4 + 5 VDC