9 2 2 0 A NCL NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/HH Cylinders 1209| | | Capacity form/unform 199/ 226 MB Heads 9| | | Seek time / track 17.0/ 3.8 ms Sector/track 36| | | Controller IDE / AT Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 1.250 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM 3565 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 50000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** BRAND BT-9121A/BT-9170A/BT-9220A PRODUCT DESCRIPTION +---------------------------------------------------------+ | |XX | |XX I | |XX N +-+ |XX T | | |XX E | | J2 |XX R J1 | | |XX F | | |XX A | | M +--+ |XX C | | S | | |XX E | | M2| | |XX +-1 +--+ |XX ++ |XX ++LED (to pins 1-2 of J2) | 1 | |XX | |XXPower +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** BRAND BT-9121A/BT-9170A/BT-9220A PRODUCT DESCRIPTION Jumper Setting ============== Correctly jumper the hard drive before installing it into the computer. The IDE/AT interface controls a maximum of two (2) hard drives. +----------------------+---+---+---+ |Drive Config. | M | S | M2| +----------------------+---+---+---+ |One Drive Master "C" |IN |OUT|OUT| |Two Drive Master "C" |IN |OUT|IN | |Two Drive Slave "D" |OUT|IN |OUT| +----------------------+---+---+---+ ********************************************************************** I N S T A L L ********************************************************************** BRAND BT-9121A/BT-9170A/BT-9220A PRODUCT DESCRIPTION Installing the Hard Drive ------------------------- Install the hard drive in accordance with the User's Manual of the computer. There are two cable that need to be connected to the IDE/AT hard drive, the 40 pin interface connector and the power connector. The power connector is keyed and can only be connected one way. The interface connector may not be keyed. Connect pin one on the hard drive to pin one on the IDE/AT adapter on the host computer. ********************************************************************** F E A T U R E S ********************************************************************** BRAND BT-9121A/BT-9170A/BT-9220A PRODUCT DESCRIPTION Important Information --------------------- The IDE/AT hard drive can only operate in AT type (286, 386 and 486) computers with an IDE Host Adapter, or with computers that have IDE/ AT integrated into the Motherboard. All BT9000A drives automatically park and lock the data heads in a dedicated landing zone when power is turned off. The heads will auto- matically unlock when power is turned on. System Setup ------------ After the IDE/AT hard drive is installed and cable ready, select a "Drive Type" in the host computer's BIOS. Normally, the "Drive Type" is set according to the number of heads and cylinders. IDE/AT hard drives are set based on CAPACITY. Always choose a "Drive Type" that is equal or less than the drive's actual "Maximum Capacity". "Drive Type(s)" that are preconfigured by the computer manufacturers are called "Standard Drive Types". "Standard Drive Types" cannot be modified. Computers that support "User Define Drive Type(s)" allow the operator to create any drive configuration. If the host computer does not have a "Standard Drive Type" that matches the IDE/AT drive's actual configuration, and does not support "User Define Drive Types", a "Standard Drive Type" that is equal or less than the drive's actual Maximum Capacity must be selected. CAUTION BIOS's that display the capacity of the "Drive Type" may be incorrect. Selecting a "Drive Type" that exceeds the actual "Maximum Capacity" will cause the drive to operate improperly. IBM/MS DOS ---------- IBM/MS DOS versions 3.xx and 4.xx support a maximum of 1024 cylinders. DOS will ignore any cylinders over 1024. Because of this limitation with DOS, the drive cannot achieve maximum capacity. To overcome this limitation use Ontrack's DiskManager along with SWBIOS.EXE and/or Translation Mode. If the computer's BIOS supports "User Define Drive Types", then reconfigure the drive type to less than 1024 cylinders.