7 2 9 0 S MAXTOR NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1751| | | Capacity form/unform 290/ MB Heads 4| | | Seek time / track 16.0/ 5.0 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 64 KB ON-BOARD Landing Zone Data transfer rate 2.800 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 71 Power: sleep W Humidity % 5 95 | 5 95 standby W Altitude km -0.061 3.048| idle W Shock g 10 | 70 seek 3.8 W Rotation RPM 3551 read/write 4.0 W Acoustic dBA spin-up 11.8 W ECC Bit MTBF h 300000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 7290S JUMPER SETTING +---------------------------------------------------------+ | +--J309 |XX | +-+-+-+-+++ |XX | +++++++++-+ ++ |XX J1 | +--+ | | +---+ || |XX | J305 J306 J307 J308 || |XX Inter- | +-+ || |XX face | J304/+-+RP301|| |XX | J303/+-+ ++ |XX | J302/+-+ ++ |XX | J301/+-+ || |XX | || |XX | RP302|| |XX | || |XX | ++ |X1 | | | |XX Power | |XX J2 +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 7290S JUMPER SETTING Jumper setting ============== x = Jumper set at factory J301 Terminator Power Selection ------------------------------- Terminator power generation may occur internally from the disk drive (when J301 is jumpered), or externally from the SCSI bus. Factory default is J301 jumpered. J302 Drive Power-Up Option --------------------------- Pin 1-2 OPEN Wait for Start Command - The disk drive will not spin-up until the initiator issues a START/STOP UNIT command with the start bit equal to one. CLOSED Start When Power Applied - The spin motor starts when power is supplied. J303 Parity Disable Option ---------------------------- The parity disable jumper, J303, enables (open, factory default) or disables (jumperred) odd parity detection in the disk drive. J304 Reserved -------------- RESERVED! J305 Reserved -------------- RESERVED! J306 Reserved -------------- RESERVED! J307/308/309 Addressing ------------------------ +---------------+------------+ | Jumper | Address | +---------------+------------+ | J309 | SEL 0 (LSB)| | J308 | SEL 1 | | J307 | SEL 2 (MSB)| +---------------+------------+ When jumpered, the corresponding bit is a 1. The SCSI bus supports connection of up to seven devices, but communication can occur only between two SCSI devices at a time. Each device has an assigned ID bit that establishes device priority on the SCSI bus. When two SCSI devices communicate, one acts as an initiator and the other as a target. The initiator orginates an operation and the target performs the operation specified by the initiator. An initiator can address up to seven other logical units (LUNs) attached to one target. The drive has only one logical unit attached. (LUN=0). J307/308/309 SCSI ID --------------------- +--------+----------+-------+-------+-------+ |SCSI ID | Priority | J307 | J308 | J309 | +--------+----------+-------+-------+-------+ | 0 | Lowest |OPEN |OPEN |OPEN | | 1 | . |OPEN |OPEN |CLOSED | | 2 | . |OPEN |CLOSED |OPEN | | 3 | . |OPEN |CLOSED |CLOSED | | 4 | . |CLOSED |OPEN |OPEN | | 5 | . |CLOSED |OPEN |CLOSED | |x 6 | . |CLOSED |CLOSED |OPEN | | 7 | Highest |CLOSED |CLOSED |CLOSED | +--------+----------+-------+-------+-------+ Each 7000 Series SCSI drive is shipped from the factory with an ID of 6. This ID designation assures sufficient jumpers are available for any address except 7 (which is usually reserved for the host system). J2 DC Power and pin connector assignments ------------------------------------------- +------------+ pin 1 +12 VDC | 1 2 3 4 | pin 2 +12 V Ground Return +------------+ pin 3 + 5 V Ground Return pin 4 + 5 VDC ********************************************************************** G E N E R A L ********************************************************************** MAXTOR SCSI INSTALLATION GENERIC INSTALLATION PROCEDURE FOR A SCSI DRIVE ----------------------------------------------------------- 1. Install a 50 pin ribbon connector making sure pin 1, which can be identified by the striped edge of the cable, is closest to the power connector on the drive. 2. Install a DC power cable to the back of the drive. 3. Verify the SCSI ID selection. Note: SCSI ID usually needs to be set to 0 to be the boot drive. The last physical device on the SCSI bus must be terminated. Any other drive or SCSI device connected between the host and the device at the end of the bus must not be terminated. 4. Apply power to the computer. 4a. When memory test is complete go into your system's Standard C-MOS set-up. (Note: There are various ways to get into C-MOS set-up, please refer to system's manual for instuctions.) 4b. Set the drive type to "Not Installed". This intelligent drive will identify itself to the SCSI host adapter. 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on it. At the A> prompt type in FDISK. At the menu options select option 1 to create a DOS partition. Another menu will appear and from those options choose 1 to create a Primary DOS partition. Select yes to make 1 large partition and it will automatically become active. Then escape from FDISK. 6. At the A> prompt type in FORMAT C:/S This does a high-level format on the drive and transfers the system files in order for the drive to be bootable. (Note: Maxtor SCSI drives are low-level formatted at the factory) 7. The drive is now bootable. As a test remove the DOS diskette from A and press reset to re-boot the computer, a C> should be displayed, the drive is now ready for operation.