D K 5 1 4 - 3 8 HITACHI NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/FH Cylinders 903| | | Capacity form/unform 330/ 382 MB Heads 14| | | Seek time / track 16.0/ 4.0 ms Sector/track 51| | | Controller ESDI Precompensation Cache/Buffer 24 KB FIFO BUFFER Landing Zone Data transfer rate 1.772 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 45 | -20 50 Power: sleep W Humidity % 8 80 | 8 90 standby W Altitude km | idle W Shock g 2 | 20 seek W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit 48 MTBF h 30000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** HITACHI DK514 PRODUCT SPECIFICATION K2500186 MARCH 15, 1988, REV. 4 +--------------+ +------------------------------------+ | +--+ +-------+ (SZ905) | +-+| J4 +-J5----+ |XX J2 || | +-------+ |XXCable || | JP162 JP163 |XXC || | ++++++1 ++++++++1 |XX || | 12++++++16++++++++ |XX |+--+ ++++1 | |+--J6 8++++JP165 |XX +-++--+ +++1 JP230|XXCable | 6+++ |XXB | +---+ |XX | | TM309 |XX J1 | | | |XX | | | |XX | +-+-+ | | |XXJ3 | A/N4 +------+ +-----+ |XXCable +---+---+ +---------------+ +----------------------+ A ********************************************************************** J U M P E R S ********************************************************************** HITACHI DK514 PRODUCT SPECIFICATION K2500186 MARCH 15, 1988 REV. 4 Jumper Setting ============== JP162/JP163 Number of bytes PCB REV. 3 or more ----------------------------------------------- +------------------+----------+ | Jumper |Number of | | Setting |byte | A drive as shipped is set as 332 +------------------+----------+ Bytes/Sector (91 Sector/Track) |JP162 (PIN 07-08) | 2048 | +------------------+----------+ |JP162 (PIN 05-06) | 1024 | +------------------+----------+ |JP162 (PIN 03-04) | 512 | +------------------+----------+ |JP162 (PIN 01-02) | 256 | +------------------+----------+ |JP163 (PIN 15-16) | 128 | +------------------+----------+ |JP163 (PIN 13-14) | 64 | +------------------+----------+ |JP163 (PIN 11-12) | 32 | +------------------+----------+ |JP163 (PIN 09-10) | 16 | +------------------+----------+ |JP163 (PIN 07-08) | 8 | +------------------+----------+ |JP163 (PIN 05-06) | 4 | +------------------+----------+ |JP163 (PIN 03-04) | 2 | +------------------+----------+ |JP163 (PIN 01-02) | 1 | +------------------+----------+ The number of sectors is determined in either of the following ways: a. Given the number of bytes/sector: Example: 332 bytes/sector are required: Total bytes/track 30,240 Number of sectors = ----------------- = ------ = 91 sec./track bytes/sector 332 Each track will consist of 90 sectors of 332 bytes each and one sector of 360 bytes. Jumper setting: JP162 (PIN 1-2) JP163 (PIN 13-14) JP163 (PIN 7-8) JP163 (5-6) 256 + 64 + 8 + 4 = 332 b. Given the number of sectors/track: Example: 51 sectors/track are required: Total bytes/track 30,240 Bytes/sector = ----------------- = ------ = 592 bytes Sector/track 51 Each track will consist of 50 sectors of 592 bytes each and one sector of 640 bytes. Jumper setting: JP162 (PIN 3-4) JP163 (PIN 13-14) JP163 (PIN 9-10) 512 + 64 + 16 = 592 JP165 Drive Address PCB REV. 1 or more --------------------------------------- +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ 8| |7 8| |7 8| |7 8| |7 8| |7 8| |7 8| |7 8| | +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ 6| |5 6| |5 6| |5 6| |5 6|XXX|5 6|XXX|5 6|XXX|5 6|XXX| +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ 4| |3 4| |3 4|XXX|3 4|XXX|3 4| |3 4| |3 4|XXX|3 4|XXX| +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ 2| |1 2|XXX|1 2| |1 2|XXX|1 2| |1 2|XXX|1 2| |1 2|XXX| +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ Address Address Address Address Address Address Address Address None 1 2 3 4 5 6 7 At the time of shipment, Drive 1 is selected. Drive address is valid from 1 to 7. Drive Address 0 is not used. JP165 Write Protect PCB Rev. 1 or more --------------------------------------- Pins 7-8 OPEN Write Enable CLOSED Write Protect At the time of shipment, "Write Enable" mode is selected. Write operation of a drive is inhibited by setting a jumper on JP165, pin 7-8, which condition will generate ATTENTION status upon receiv- ing of WRITE GATE-N signal. JP164/JP162 Hard Sector/Soft Sector ------------------------------------ The drive with Hard Sector mode issues SECTOR clock on J1-pin 16 and J2-pin 2, and with Soft Sector mode does ADDRESS MARK FOUND-N on J1- pin 16 and J2-pin 2. "Set Configuration" command takes precedence over this Jumper Setting function. PCB Rev. 1, 2 ------------- JP164 Pins 9-10 OPEN Soft Sector Pins 9-10 CLOSED Hard Sector PCB Rev. 3 or more ------------------ JP162 Pins 9-10 OPEN Soft Sector Pins 9-10 CLOSED Hard Sector A drive as shipped is set as "Hard Sector" mode Terminator Module (TM312 or TM309) and Radial Switch (JP230, pin 1-6) --------------------------------------------------------------------- Each drive in Radial connection of cable B and the last end of the drives in Daisy Chain connection of cable B should be terminated. Since a terminator module (TM312 or TM309) and Jumper Sockets on JP230 are provided to all drives as shipped, remove both of them except the last drive's ones in case of Daisy Chain connection. PCB Rev. 1, 2 ------------- |Terminator |JP230 pins 1-6 | (TM312) | -----------------------------------+-----------+---------------- Single drive on cable B | MOUNTED | CLOSED -----------------------------------+-----------+---------------- All drives in Radial connectiom | MOUNTED | CLOSED -----------------------------------+-----------+---------------- The last drive in Daisy Chain | MOUNTED | CLOSED -----------------------------------+-----------+---------------- All drives except the last one in | REMOVED | OPEN Daisy Chain | | PCB Rev. 3 or more ------------------ |Terminator |JP230 pins 1-6 | (TM309) | -----------------------------------+-----------+---------------- Single drive on cable B | MOUNTED | CLOSED -----------------------------------+-----------+---------------- All drives in Radial connectiom | MOUNTED | CLOSED -----------------------------------+-----------+---------------- The last drive in Daisy Chain | MOUNTED | CLOSED -----------------------------------+-----------+---------------- All drives except the last one in | REMOVED | OPEN Daisy Chain | | A drive as shipped is mounted with Terminator Module and Jumper Sockets (three) on JP230.